Key takeaways
- Wrong controller mode. Many updaters require the drive to be on the standard AHCI or NVMe path, not behind a RAID or Intel RST/VMD setup. Makers such as Samsung, Crucial, Western Digital and others describe supported configurations in their own utility documentation.
- Drive is the system disk. Some tools need to restart the computer to apply the update to the boot drive.
- Using the wrong firmware. Firmware is model-specific, and sometimes capacity-specific. Packages for a similar model name can be wrong.
- Power interruption. A power cut, forced shutdown, or sleep during the update can interrupt it. On laptops, keep the charger connected.
- Interference from other software. Security tools, drive encryption, or other disk utilities may block low-level drive access.
- Enclosure or adapter. USB enclosures and adapters often do not pass firmware commands to the drive.
- Locked or encrypted state. A drive with hardware encryption or a password set may refuse updates until unlocked.
If an SSD firmware update failed, do not keep retrying blindly: power the PC down cleanly, then check whether the drive still appears in the BIOS and the maker’s utility. If it does, the original firmware is usually still running and the update can be attempted again after the fixes below. If it does not appear, contact the drive maker’s support before doing anything else.
First, Stay Calm and Protect Your Data
A failed update does not always mean a broken drive. Many failures happen because the updater could not talk to the drive, not because the flash was altered. Even so, firmware updates carry risk, which is why makers tell users to back up first. If the drive still works, copy your important files off now, before another attempt.
What the Failure Might Look Like
| What you see | Likely meaning | Next step |
|---|---|---|
| Updater says “failed” but the drive works and shows the old version | Update did not begin or was rejected | Back up, fix the cause, retry |
| Updater says it needs a restart or power cycle | New firmware activates on reboot | Shut down fully and power on again |
| Drive missing from the utility but visible in BIOS | Driver or controller mode issue | Check storage drivers and mode |
| Drive missing from BIOS | Connection problem or drive in a faulty state | Reseat, try another slot, contact the maker |
| Drive shows a strange name or tiny capacity | Drive in a recovery or fault mode | Stop; contact maker support |
| Update tool will not detect the drive at all | Unsupported model, RAID mode, or external enclosure | Read the maker’s supported-configuration notes |
Common Causes
- Wrong controller mode. Many updaters require the drive to be on the standard AHCI or NVMe path, not behind a RAID or Intel RST/VMD setup. Makers such as Samsung, Crucial, Western Digital and others describe supported configurations in their own utility documentation.
- Drive is the system disk. Some tools need to restart the computer to apply the update to the boot drive.
- Using the wrong firmware. Firmware is model-specific, and sometimes capacity-specific. Packages for a similar model name can be wrong.
- Power interruption. A power cut, forced shutdown, or sleep during the update can interrupt it. On laptops, keep the charger connected.
- Interference from other software. Security tools, drive encryption, or other disk utilities may block low-level drive access.
- Enclosure or adapter. USB enclosures and adapters often do not pass firmware commands to the drive.
- Locked or encrypted state. A drive with hardware encryption or a password set may refuse updates until unlocked.
Step-by-Step Recovery
- Do not interrupt anything further. If the updater is still running, wait for it to finish or time out.
- Power down fully, wait about a minute, and boot again. Some updates apply only after a complete power cycle.
- Check the BIOS or UEFI storage list. The menu name varies by motherboard maker, so consult your manual if you cannot find it. Note whether the drive and its capacity appear.
- Check the maker’s utility. Look at the firmware version shown. If it shows the new version, the update worked despite the message.
- Back up data if the drive is readable.
- Unplug the PC and reseat the drive. Turn the power off and unplug before opening the case. Reinstall the M.2 drive or SATA cable securely, or try another slot.
- Review the update requirements in the maker’s release notes: supported operating system, controller mode, minimum battery level, and whether the drive must be a secondary disk.
- Retry once from the maker’s official tool with the drive connected directly to the motherboard, not through a USB adapter, and with stable power.
- Contact support. If the drive is undetected or shows an odd identity, open a ticket with the maker and mention the model, firmware version and what the updater reported. Warranty may apply.
When the Drive Is Not Detected
If the drive fails to appear in BIOS after a failed update, try a different M.2 slot or a different computer. Check that the slot is not disabled by another drive occupying a shared lane, which some motherboards do. If it still does not appear, treat it as a warranty case. Do not attempt unofficial recovery tools or firmware images from unknown sources, since the wrong file can permanently damage the drive.
Should You Update at All?
| Situation | Reasonable approach |
|---|---|
| Drive works fine and no known issue | Updating is optional; many users leave it |
| Maker published a fix for a problem you actually have | Back up, then update using the official tool |
| Drive is in a RAID or enclosure | Check whether the tool supports it before trying |
| Laptop on battery | Plug in the charger first |
| Critical machine with no backup | Make a backup before touching firmware |
Common Mistakes
- Skipping the backup because the update seems routine.
- Downloading firmware from a forum or a third-party site instead of the maker.
- Running the updater while a game, antivirus scan, or large copy is active.
- Forcing a shutdown mid-update.
- Repeating the update many times in a row without reading the error.
- Updating through a USB enclosure that cannot pass the commands.
Preparing Properly Next Time
Most firmware trouble is avoidable with preparation. Read the release notes on the maker’s support page to see what the update changes and whether it applies to your drive. Note the current firmware version and the drive’s exact model and capacity. Close games, scanners, and backup software, and disable any sleep timers for the duration. On a laptop, keep the charger connected and the battery reasonably full. Where the maker offers both a Windows utility and a bootable tool, follow the method its instructions prefer for your setup. If the drive is part of a RAID array, a laptop with a vendor-locked storage stack, or a prebuilt system whose manufacturer controls drive updates, check that maker’s guidance first, because their support terms can differ. Keep a short written record of what you did and any message shown. If a problem appears, that record speeds up support, and it helps a technician work out whether the cause lies in the drive, the controller mode, or the software. Patience matters too: an update can look frozen while the drive is writing, so allow the tool to finish before intervening.
Frequently Asked Questions
Can a failed firmware update brick an SSD?
It can in rare cases, especially if power is lost at a critical moment. Most failures leave the drive on its previous firmware, so check the version in the maker’s tool before assuming damage.
Will I lose my data?
Firmware updates are not intended to erase data, but makers still advise a backup because problems can happen. If the drive is still readable, copy your files before another attempt.
Is it safe to retry the update?
Once, after addressing the likely cause, yes. Use the maker’s official tool, stable power and the correct controller mode. If it fails again, stop and contact support.
Why does the update tool not see my drive?
Common reasons are RAID or Intel VMD mode, a USB enclosure, an unsupported model, or a missing driver. The maker’s utility documentation lists supported setups.
Does the warranty cover a failed update?
That depends on the maker’s terms. If you used their official tool and the drive is faulty afterwards, support is the place to ask. Keep records of the error message and model details.
FAQ
Can a failed firmware update brick an SSD?
Will I lose my data?
Is it safe to retry the update?
Why does the update tool not see my drive?
Does the warranty cover a failed update?
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.